Baxi 754 Manual do Utilizador

5131652/01© Baxi Heating U.K. Limited 2008.Model 754INSET LIVE FUEL EFFECT GAS FIREFitted with one of the following fascia.Amour, Aspect, Aspect Glass

4.2.1.1 ‘Hole-in-the-wall’ installations. It is recommended thata hearth should beinstalled as in figure 1.If a hearth is not fitted,the fire must be

4.2.2 To a fireplace incorporating ametal flue box complying with theconstructional requirements of thecurrent edition of BS EN 1856 Part 1or BS715.

materials to be used are stainless steel or aluminium as specified in BS EN 1856Part 1 or BS715. The liner must be sealed to the surrounding area abov

4.12 This appliance must not be installed in any room that contains a bath or showeror where steam is regularly present.4.13 An extractor fan may only

increased by at least 2mm all round.If the cladding projects forward fromthe fixing plane of the fire theclearance at the top of theappliance must be

Page 15© Baxi Heating U.K. Limited 2008.Figure 5. Appliance dimensions and clearances - SEE TABLE ON NEXT PAGE (Fascia may differ fromthat shown)INSTA

Page 16© Baxi Heating U.K. Limited 2008.INSTALLER GUIDEKey DescriptionModelAmourAspect Eclipse FascinationLandscape& SerenityVisiaTranquility &am

5. PACK CONTENTS1 Burner & Hotbox Unit.1 Nut & olive for 8mm inlet pipe.1 Inlet ‘T’ Connector.1 Flue restrictor plate.2 Screws (For flue restr

Page 18© Baxi Heating U.K. Limited 2008.INSTALLER GUIDEFigure 6. Pack contents continued

Carefully remove all the contents. Take special care in handling the ceramic fueleffects. Check that all the listed parts are present and in good cond

© Baxi Heating U.K. Limited 2008.All rights reserved. No part of this publication may be reproduced in any material form(including photocopying), stor

the area covered by the fascia. The cladding must also not touch the fascia (Seefigure 4). We suggest that the actual fascia is used as a template to

7. IGNITION CHECKBefore attempting to install, it isworth checking that the ignitionsystem performs satisfactorily.Set the control knob to the offposi

9. PREPARING APPLIANCE FOR INSTALLATION1. Detach the spillage plate from the hotbox byremoving the four screws (See figure 9).2. Remove the protective

10. Fit the two “U” section seals to thebottom edges of the hotbox side flanges(See figure 12).11. It is important that the grommetsupplied in the loo

fitted to the outer rear edges of the sideand top flanges of the hotbox. Cut a485mm length of foam seal. Be carefulnot to stretch the seal when measur

10.2 Method 2 - Cable retentionand floor fixing.1. Make sure that the relevant areasat the fireplace back or floor aresound enough to take the eyebolt

7. Place the hotbox fully back into the fireplace opening so that it is sealed againstthe fireplace front surround.8. Drill a hole into the fireplace

10.3 Sealing floor front - all installations.Using the floor sealing tape supplied, seal thebottom of the hotbox to the fireplace and hearthfloor (See

11.3 Preliminary burner checks.Some burner operations can be checked at this stage. Checking now will mean thatless disassembly will be required if an

11.5 Fitting the lower hotbox baffle to the‘Fascination’model.The lower hotbox baffle is supplied for use whenfitting the ‘Fascination’ model into ele

Safety First.Valor Fires fires are CE Approved and designed to meet the appropriate BritishStandards and Safety Marks.Quality and Excellence.All Valor

13.1.2 Operating the burner.Turn the control knob anti-clockwise to ‘HIGH’ (Depress the knob slightly to get pastthe pilot ignition position). The mai

13.3 Flame supervision and spillage monitoring system.This pilot unit includes a system that will automatically shut off the gas supply if thepilot fl

3. The fasciadecorative trim ismade up of foursections. A bottomand top section ofequal length andtwo shortersections of equallength that are theside

8. Locate the top trim as infigure 31.14.2 Fitting the Landscape, Visia and Serenity fascia.1. Supplied with the fire are twofascia securing brackets

4. The lower inner sides of the fascia should sit on top of the fascia securing brackets.The fascia will need to be re-positioned if the fascia sides

14.4 Fitting the Glass panel to the ‘Fascination’ , ‘Tranquility’ and ‘Aspect Glass’fascia (See figure 39).1. Supplied with the trim packare four cyli

Important: The spacersprovided with the trim packmust always be fitted.Never reduce the depth ofthe spacers in any way.Always replace thespacers with

3. Advise the customer how to operate the appliance. Point out that lightinginstruction details are on the metal plate attached at the bottom of the a

16. SERVICING & PARTS REPLACEMENT Always turn off the gas supply before commencing any servicing (Theappliance inlet “T” connector incorporates a

16.1 To remove the fascia.(Amour, Aspect, Aspect Glass, Eclipse, Tranquilityand Fascination models).1. Eclipse model only- Remove the upper fascia tr

Page 4© Baxi Heating U.K. Limited 2008.INSTALLER GUIDEINSTALLER GUIDEFOR OWNER GUIDE SEE PAGES 44 TO 59

16.2 To remove the burner unit.1. Remove the fascia as in section 16.1.2. Remove the ceramic fuel effect pieces.3. Detach the spillage plate from the

16.3 To remove the pilot unit.1. Remove the burner unit (See section 16.2).2. If lying the burner on its back, ensure that the worksurface is suitably

16.5 To remove the piezo generator.1. Remove the gas valve as section 16.4.2. Make sure that the tap is in the off position.3. Remove the circlip hold

16.8 To remove the main burner injector.(See figure 51).1. Remove the burner (See section 16.7).2. Remove the burner clamping screw (See figure51)3. U

Page 44© Baxi Heating U.K. Limited 2008.OWNER GUIDEOWNER GUIDEFOR WARRANTY AND SERVICE INFORMATIONSEE PAGES 55 TO 59

LIST OF CONTENTSSection PageSAFETY 46APPLIANCE DIMENSIONS 47GAS CONSUMPTION 49OPERATING YOUR FIRE 50The Oxysafe flame sensing and flue blockage saf

SAFETYDo have the fire installed by a competent person. In the United Kingdom, installationmust be in accordance with the latest edition of the Gas Sa

by heat. They may, therefore, scorch or become discoloured when close to a heatingappliance. Please bear this in mind whenever you are considering red

Page 48© Baxi Heating U.K. Limited 2008.OWNER GUIDEKey DescriptionModelAmourAspectEclipseFascinationLandscape& SerenityVisiaTranquility &Aspec

GAS CONSUMPTIONModel 754 when fitted with Amour, Aspect, Eclipse, Landscape, Serenity andVisia fascia.Has a maximum natural gas input of 5.1kW (Gross)

CONTENTSSection Heading PageINSTALLER GUIDE 4 - 43OWNER GUIDE 44 - 591. SAFETY 62. ACCESSORY LIST 63. APPLIANCE DATA 74. GENERAL INSTALLATION REQUI

OPERATING YOUR FIREThe Oxysafe flame sensing and flue blockage safety system.For your safety, this appliance is fitted with a flue blockage safety dev

Eclipse and Fascination models.To gain access to the control knob lower thebottom front cover. To do this, support the topedges of the lower front cov

the knob reaches the “HIGH” position.Note:i) If the flames go out while setting the control, repeat the full lighting procedure.If the flames repeated

CLEANING YOUR FIRETo maintain the high performance and quality finish of your fire please follow theseguidelines: Before attempting to clean the fir

 In the unlikely event of soot forming, light coatings will usually be burnt off duringthe normal operation of the fire. Should any soot accumulat

MAINTENANCERegular maintenance.In order to achieve and maintain high levels of personal safety and performanceefficiency, it is essential that the ope

What you need to do if you experience a problem with the operation of the fire:  You should always contact your installer first, because the cause o

Page 57© Baxi Heating U.K. Limited 2008.OWNER GUIDE

Page 58© Baxi Heating U.K. Limited 2008.Installer Details (Block Capitals)Installer NameCorgi Registration Number.Company Name.Company AddressCompany

Page 59© Baxi Heating U.K. Limited 2008.Brand (Please tick)Baxi Valor Wonderfire Other...D D M M Y YDate of InstallationFascia

1. SAFETYInstallerBefore continuing any further with the installation of this appliance please read the following guide to manual handling: The appr

© Baxi Heating U.K. Limited 2008.

3. APPLIANCE DATA* When converted using conversion kit number 05754M1.The appliance information label is located on a plate at the base of the fire. T

The efficiency of this appliance has been measured as specified in BS 7977 - 1 andthe result is as below :ModelEfficiency % (Gross)Amour, Aspect, Ecli

4. GENERAL INSTALLATION REQUIREMENTS4.1 The installation must be in accordance with these instructions.For the user’s protection, in the United Kingdo