Baxi 739 Manual do Utilizador

5113426/01INSTALLER GUIDEWe trust that this guide gives sufficient details to enable this appliance to be installedand maintained satisfactorily. Howe

Page 10INSTALLER GUIDETable 1. Flue sizing table.

4.7The minimum height from the top of the hearth to the underside of any shelf madefrom wood or other combustible materials is as follows: -! For a s

4.12Propane gas appliances must not be installed in a room that is built entirely belowground level (see BS 5871 Part 3).4.13 If the appliance is to b

4.14.2Non-combustible side projections to be 75mm from the fireplace opening (Seefigure 4)4.15 The appliance is fitted with an A.S.D (Atmosphere sensi

6. INSTALLATION OF APPLIANCEINSTALLATION6.1 Fireplace size.The fireplace must comply with the requirements described in section 4.6.2 Fireplace flue

6.3.2 Burner PositioningThe two tags at the side of the burner can be foldedagainst the side of the burner tray. This may be requiredfor installations

6.3.3 Locating the burner.! Place the burner assembly inposition (If installing into a 'Liberty'casting the rear support plate on theburner

Turn on the gas supply and pressure check the installation pipework for gas soundness.In the United Kingdom (GB) check in accordance with the current

Remove the pressure gauge and replace the test point sealing screw.3. Relight the appliance. Turn to the maximum output position and test around these

3. Locate the firefront as in figure 14. Thescrew heads should locate into the slots in theburner tray. 4. The lower 'ashpan' casting should

Safety First.Baxi Fires Division fires are CE Approved and designed to meet the appropriate BritishStandards and Safety Marks.Quality and Excellence.A

10. FULL OPERATING CHECKSSpillage check.For installations without the 'Liberty' casting! A spillage check must be made beforeleaving the in

Page 21INSTALLER GUIDE! If the above test is satisfactory, open all internal connecting doors, hatches, etc. inthe room. Keep all doors and windows th

! Recommend that the appliance should be serviced and the chimney inspected by acompetent person at least annually.11. SERVICING & PARTS REPLACEME

11.2 To remove the complete burnerunit.1. Remove the firefront and place in asafe position.2. Remove the ceramic fuel effect. 3. Close the valve in th

10. Remove the gas valve11. Refit in the reverse order.11.5 To remove the piezogenerator.1. Remove the gas valve as insection 11.4.2. Make sure that t

11.8 To remove the main burner injector.(See figure 22).1. Remove the burner (See section 11.7).2. Remove the burner clamping screw (See figure22)3. U

CONTENTSSection Page1. SAFETY 32. LIST OF ACCESSORIES 43. APPLIANCE DATA 54. GENERAL INSTALLATION REQUIREMENTS 65. UNPACKING 136. INSTALLATION OF

2. LIST OF ACCESSORIESValor and B&Q modelsDescription Part NumberAll ModelsLPG Conversion kit 0595211‘Quattro’ / ‘Anthem’, ‘Majestic’ and Models n

Description Part NumberBlenheim Firefront (16 inch Fret)! Brass effect 9800040! Antique (Black & Brass effect) 9800075! Chrome effect 980007

*When converted using kit 05952114. GENERAL INSTALLATION REQUIREMENTS4.1 The installation must be in accordance with these instructions.For the user’s

In England and Wales, the current edition of the Building Regulations issued by theDepartment of the Environment and the Welsh Office. In Scotland the

200mm diameter factory made insulated flue manufactured to BS4543.175mm diameter flue pipe. See BS6461 Part 1 for suitable materials.The minimum effec

Page 9INSTALLER GUIDEFigure 1. Hearth and fireplace openingFigure 2. Hearth and fireplace opening for installations using theLIBERTY CASTING ONLY