Baxi 739 Guia de Instalação

5117291/04© Baxi Heating U.K. Limited 2010.Model 939Heat EngineOPEN DECORATIVE GAS FIRE(GC No. 32-032-54)INSTALLER: Please leave this guide with the o

3.2 Ventilation requirements.Normal adventitious ventilation is usually sufficient to satisfy the ventilationrequirements of this appliance. In GB ref

3.7 Fireplace preparation.3.7.1 If the fireplace opening is an underfloor draught type, it must be sealed to stopany draughts.3.7.2 The surface of the

3.9 Fireplace clearances.3.9.1 Combustible side projections up to 75mm forward of the fixing plane of the fireare to be a minimum of 125mm from the fi

For installation with and without the Spanish basket casting. If a hearth is not fitted or if a reduced depth hearth is fitted, the fire must beinst

Page 14© Baxi Heating U.K. Limited 2010.INSTALLER GUIDEFigure 3. Hearth and fireplace openingFigure 4. Hearth and fireplace opening for installations

Page 15© Baxi Heating U.K. Limited 2010.INSTALLER GUIDETable 5. Flue sizing table.

4. UNPACKINGContents:1 Burner assembly.1 Nut & olive for 8mm inlet pipe. 4 Screws.4 Plastic screw plugs.1 Fuel bed matrix support plate.2 Self tap

5.3 Installation of the burner unit 5.3.1 Prior to installation of the burner therear ceramic support bracket must be fitted(See figure 6). Secure wit

5.3.3 Locating the burner. Mark onto the floor, the position of the two fixing holes in the front fixing bracket(See figure 9). Without disturbing

6.1 Preliminary burner checks.Some burner operations can be checked at this stage. Checking now will mean thatless disassembly will be required if any

© Baxi Heating U.K. Limited 2010.All rights reserved. No part of this publication may be reproduced in any material form(including photocopying), stor

7. FITTING THE FIREFRONT A slotted firefront with a minimum free area as shown in figure 12 must always beused. Place the decorative firefront on

Page 21© Baxi Heating U.K. Limited 2010.9. FULL OPERATING CHECKS9.1 Spillage check. A spillage check must be made beforeleaving the installed applian

The valve is located in the body of the tap. The valve should operate within 60seconds of the pilot going out. If the valve does not operate within th

10. SERVICING & PARTS REPLACEMENTAlways turn off the gas supply before commencing any servicing (Theappliance inlet ‘T’ connector incorporates an

10.2 To remove the complete burner unit.1. Remove the firefront and place in a safe position.2. Remove the ceramic fuel effect. 3. Close the valve in

10.5 To remove the piezo generator.1. Remove the gas valve as in section 10.4.2. Make sure that the tap is in the off position.3. Remove the circlip h

Page 26© Baxi Heating U.K. Limited 2010.OWNER GUIDEOWNER GUIDE

LIST OF CONTENTSSection PageSAFETY 28GAS CONSUMPTION 29OPERATING THE FIRE 30The Oxysafe flame sensing & flue blockage safety system. 30To light

SAFETYDo have the fire installed by a competent person. In the United Kingdom, installation must be in accordance with the latest edition of the Gas S

Do wait three minutes before attempting to relight if the fire is switched off or theflames are extinguished for any reason. (Your fire is fitted with

Safety First.This gas fire is CE Approved and designed to meet the appropriate British Standardsand Safety Marks.Quality and Excellence.This fire has

OPERATING THE FIREThe Oxysafe flame sensing & flue blockage safety system.For your safety, this appliance is fitted with a flue blockage safety de

While cooling, the ceramic fuel effect may make some crackling noises. This is quitenormal. If the flames go out while setting the control, repeat t

CLEANING YOUR FIRETurn the fire off and allow it to cool completely before attempting any cleaning. Notethat the fire will retain heat for some time a

CERAMIC FUEL EFFECT REFITTINGThe installer and owner guide for the ceramic fuel effect is separate from this guide.The installer may have attached it

MAINTENANCERegular maintenance.In order to achieve and maintain high levels of personal safety and performanceefficiency, it is essential that the ope

© Baxi Heating U.K. Limited 2010.

© Baxi Heating U.K. Limited 2010.

Page 4© Baxi Heating U.K. Limited 2010.INSTALLER GUIDEINSTALLER GUIDEFOR OWNER GUIDE SEE PAGES 26 TO 34

CONTENTSSection Heading PageINSTALLER GUIDE 4 - 25OWNER GUIDE 26 - 341. SAFETY AND UNPACKING 72. APPLIANCE DATA AND EFFICIENCY 82.1 General informat

CONTENTS (Continued)Section Heading Page7. FITTING THE FIREFRONT 208. FITTING THE CERAMIC FUEL EFFECT 209. FULL OPERATING CHECKS 219.1 Spillage che

1. SAFETY AND UNPACKINGInstallerBefore continuing any further with the installation of this appliance please read the following guide to manual handli

2. APPLIANCE DATA AND EFFICIENCY2.1 General information.*When converted using kit 05952112.2 Efficiency.There are no specific thermal efficiency requi

3. GENERAL INSTALLATION REQUIREMENTS3.1 Regulations, Standards and Law.The installation must be in accordance with these instructions.For the user’s p