Baxi 339 Manual do Utilizador

© Baxi Heating U.K. Limited 2010.600B687/14Model 339Heartbeat Oxysafe 2LIVE FUEL EFFECT GAS FIRE(GC No. 32-032-29)We trust that this guide givessuffic

 In Scotland, the current edition of the Building Standards (Scotland) Regulations issued by the Scottish Executive. In Northern Ireland, the curren

5.5 Chimney preparation.5.5.1 If the appliance is intended to be installed to a chimney that was previouslyused for solid fuel, the flue must be swept

5.7 Fireplace clearances.5.7.1 The minimum allowable distance from the outside of the appliance fascia to acorner wall having combustible material or

5.8 The Flue spigot.5.8.1 The flue spigot and any spigot extensionmust be capable of passing through the closureplate by at least 15mm with a minimum

5.9. The hearth.The appliance must be mounted on a non-combustible hearth except when theconditions in section 5.10.3 are met (N.B. conglomerate marbl

The fireplace opening must be within the following dimensions:1The total height of the closure plate is 660mm and will accommodate a maximumopening he

5.10.4 Metal flue box.The appliance can be installed to a metal flue box conforming to BS715 with aminimum internal depth of 200mm. Incombustible mine

safely dispersed into the outside atmosphere. Where the appliance is connectedto an unlined brick chimney it is generally unnecessary for the chimney

screws each side of the window frame and lifting the unit clear. 9. Remove the ceramic coal fuel effect pack from thefirebox and keep it safe.10. Befo

6.4 Fitting the closure plate.(See figure 9).The closure plate has an opening at thebottom for a central gas feed pipe. Thegap between the pipe and th

© Baxi Heating U.K. Limited 2010.All rights reserved. No part of this publication may be reproduced in any material form(including photocopying), stor

6.4.2. Wall mounting.(See figure 11).The closure plate must be fittedand sealed to the hearth andfireplace opening using suitableheat resistant materi

placing the fire in position and marking the wall through the holes in the back panel.Drill and plug the holes using no.10 wall plugs. Place the fire

8. CONTROL AND PRESSURE CHECKS8.1 Check control settings.1. If closed, open the isolating valve at the inlet ‘T’ connector.2. To help in checking the

8.3 Check burner pressure.The appliance is pre-set to give the correct heat input at the inlet pressure shown insection 4 of this manual. No adjustmen

6. If the above test is satisfactory, open all internal connecting doors, hatches, etc. inthe room. Keep all doors and windows that open to the outsid

11. FINAL REVIEW COMPLETE THE INFORMATION CONTAINED IN THE WARRANTY ANDSERVICE SECTION OF THE OWNER GUIDE (See last pages of the OWNERguide). Reche

12. SERVICING AND PARTS REPLACEMENT Always turn off the gas supply before commencing any servicing (The applianceinlet "T" connector incorp

12.1 Cleaning the window and fuel effect (without removing the fascia).Important: Before commencing work read the safety notes at the start ofsection

12.2 To remove the fascia.1. Remove the control knob by pulling clear of the gas tap spindle.2. Remove the control bezel by unscrewing two screws.3. D

12.7 To grease the control tap.1. Detach the tap and remove the piezo generator as section 12.6 making sure thatthe tap is in the ‘off’ position.2. Re

Safety First.Valor Fires fires are CE Approved and designed to meet the appropriate BritishStandards and Safety Marks.Quality and Excellence.All Valor

12.9 To remove the complete burner module, pipes and pilot.1. Remove the fascia as section 12.2.2. Remove the ceramic fuel effect assection 12.4.3. Su

Page 31© Baxi Heating U.K. Limited 2010.OWNER GUIDEOWNER GUIDEFOR WARRANTY AND SERVICE INFORMATIONSEE PAGES 40 TO 43

LIST OF CONTENTSSection PageIMAGE 33SAFETY 34APPLIANCE DIMENSIONS 36GAS CONSUMPTION 36OPERATING YOUR FIRE 37The Oxysafe flame sensing and flue bloc

IMAGEPage 33© Baxi Heating U.K. Limited 2010.OWNER GUIDE

SAFETYDo have the fire installed by a competent person. In the United Kingdom, installationmust be in accordance with the latest edition of the Gas Sa

Do provide a minimum clearance of 100mm between the fascia sides and any cornerwall having combustible material or other combustible surface which pro

APPLIANCE DIMENSIONSGAS CONSUMPTIONHas a maximum natural gas input of 5.1kW (Gross).Has a maximum natural gas output of 3.6kW. Has a minimum natural g

OPERATING YOUR FIREThe Oxysafe flame sensing and flue blockage safety system.For your safety, this appliance is fitted with a flue blockage safety dev

The burner settings are: We recommend that the fire is set at position 4 for the first 10 minutes after lightingto warm up the chimney and so obtain

CLEANING YOUR FIRETo maintain the high performance and quality finish of your Valor Fires fire, pleasefollow these guidelines: Before attempting to cl

Page 4INSTALLER GUIDE© Baxi Heating U.K. Limited 2010.INSTALLER GUIDEFOR OWNER GUIDE SEE PAGES 31 TO 43

WARRANTY AND SERVICEStandard Warranty Terms & ConditionsThe warranty is for 12 months subject to contract.In the United Kingdom servicing can be c

When calling heateam, it would be helpful if you could have the following informationto hand:-1. Fire serial number (Located on the information label

Page 42© Baxi Heating U.K. Limited 2010.OWNER GUIDETo be completed by installer:Installer Details (Block Capitals)Installer NameGas Safe Register or C

Page 43© Baxi Heating U.K. Limited 2010.Brand (Please tick)Baxi Valor Wonderfire Other...D D M M Y YDate of InstallationFascia

© Baxi Heating U.K. Limited 2010.

CONTENTSSection Heading PageINSTALLER GUIDE 4 - 30OWNER GUIDE 31 - 431 IMAGE 62 SAFETY 73 LIST OF ACCESSORIES 74 APPLIANCE DATA AND EFFICIENCY

CONTENTS (Continued)Section Heading Page8 CONTROL AND PRESSURE CHECKS 228.1 Check control settings. 228.2 Flame supervision and spillage monitoring

2. SAFETYInstallerBefore continuing any further with the installation of this appliance please read the following guide to manual handling: The appr

4. APPLIANCE DATA AND EFFICIENCY4.1 Appliance data.Under no circumstances is this fire to be converted to LPG. An LPG conversion kitdoes not exist fo

The conversion of net efficiency to gross was achieved by multiplying the netefficiency by the following conversion factor from Table E3 of SAP 2005,